Sie sind nicht angemeldet! Jetzt kostenlos im Forum registrieren, weniger Werbung sehen, aktiv teilnehmen und weitere Vorteile nutzen! Diese Website nutzt Cookies. Bitte beachten Sie unsere Datenschutzerklärung.
Ich hatte dasselbte Problem mit meinen neuen Laptop. Total keine COM Schnitstelle im Laptop. USB->Seriel geht nicht. Jetzt habe ich einen PCcard (den Exsys EX-1350). Es ist eine PCcard 16 und 32 bit to seriel und es funktioniert 1A mit das One-stop Interface.
Das Problem hatte ich auch schon mal, geht ganz einfach:
Festplatte aus dem Laptop raus, via USB an einen Computer mit CD-ROM und dann die ganze WIN98 CD (am besten gleich mit allen updates) auf ein Verzeichnis WIN9 auf die Platte gepackt. Dann alten Lappi mit Diskette starten und aus dem Verzeichnis aus C:\WIN98\ heraus installieren ... fertig.
Gruss
Michael
Hmm, allerdings sind laptop festplatten anders pollig als pc festplatten und wie soll ich das dann da anschliessen? ich habe noch nicht von so einem Kabel gehört, womit man lappi festplatten an einen PC anschließen kann. Aber bitte, belehrt mich eines besseren.
Gruß
__________________ Ketten raus, Kragen hoch [Bass Sultan Hengzt]
Das Interface funktioniert bei mir immer noch nicht. Habe mir jetzt einen älteren PC besorgt, mit normalen COM-Port. Aber weder CS 6.5 läuft noch 6.1 (Naja, diese english/russische version läuft, aber er sagt immer modul not respond).
Es leuchten am LED 4 Diaoden POWER und 3 Lines. Bei 6.5 sagt er Bad Communication blablabla. Habe ich den Stecker nicht am PC merkt er das sofort. Bei 6.1 kann ich den stecker am Fahrzeug abziehen und er läuft weiter.
Bei meiner Version von CS 6.5 weiß ich, mehr oder weniger, das sie funktioniert, da mir jemand aus dem Forum diese gemailt hat. Allerdings ist das sehr merkwürdig mit 6.1, da diese zwar scannt aber ich denke nicht eine wirkliche Verbindung hat.
Meint Ihr es ist kaputt??? Achso, habe natürlich die Zündung angehabt, sprich Schlüssel auf Position 2.
Vielleicht hat jemand eine Idee?!?! Ansonsten schicke ich es zurück und ärgere mich das ich es nciht gleich in D bei Ibäh geordert habe. Jetzt wird das wieder dauern mit dem hin- und her geschicke.
Hi Mike,
habe es zwar nicht in DE, aber hier mal ein Hinweis von Carsoft selber zu Deinem Problem:
Pre-Installation Instructions:
IMPORTANT: Close all open programs and background tasks, including Virus Scanners,
and communications software. If Antivirus (such as Norton Antivirus, or MacAfee),
System Utilities or Crash Guard (such as Norton System Utilities, System Commander, etc,),
Communications Programs (such as Nokia Communication Suite, PC Anywhere, etc.) are
running during installation or use of Carsoft, communications with vehicle modules may be
slowed or may not be possible. Disable background programs or remove them from the Start
Menu prior to installing and using Carsoft.
Installing the Software CD:
1. Insert Carsoft MB CD ROM in your CD ROM Drive The program should start installing, Skip to 7.
If it does not, then:
2. Click START
3. Click RUN
4. Click BROWSE
5. Select CD ROM Drive in the LOOK IN field
6. Click SETUP, then follow instructions.
IMPORTANT: You must accept the terms of the Carsoft license agreement
in order to install this product. If you do not accept the terms, click no and return
your product to the place of purchase for a refund.
PLEASE WRITE THE SERIAL NUMBER FROM YOUR SCREEN ON THE ACTIVATION FORM!
7. Click OK
8. Click FINISH, and then restart your computer.
Installing the Diagnostic Cable:
Locate 9-Pin Serial Port. Serial Port must be identified in hardware settings as COM1.
If it is not, call Tech Support for assistance. Connect Carsoft MB Adaptor Cable to Serial Port
and screw finger-tight. Do not over tighten screws.
Important: If your computer does not have a serial port, a PCMCIA serial card must be used.
A USB to Serial adaptor is not recommended and not supported in Carsoft.
A PCMCIA adaptor card is not included in Carsoft.
Please refer to the installation instructions that come with your PCMCIA Card.
Remember to periodically check our website for service packs and update information.
[quote=MikeLorey]Ach, hat da vielleicht noch jemand was auf deutsch für mich???
Hallo Mike,
meine Software ist auch englisch. Ich kann dir aber die Fehlercodedatein in deutsch schicken. Das sieht dann so aus, das die Programmbedienung englisch ist, aber dann die Ausgabe der Fehlercodes und Beschreibung dazu deutsch ist.