BMW 7er, Modell E32 |
|
|
Varianten |
|
Detail-Infos |
|
Interaktiv |
|
- Anzeige -
|
|
|
|
|
|
|
|
04.07.2020, 22:40
|
#31
|
Neues Mitglied
Registriert seit: 25.06.2020
Ort: Ukraine
Fahrzeug: BMW E32-735i (02/1990)
|
Thanks in advance ! May I use Dextron 3 not synthetic oil ? What will happen if kick down switch not grounded of rust floor ? Will car go to limp mode ?
Geändert von Andrew1Q (04.07.2020 um 22:46 Uhr).
|
|
|
04.07.2020, 23:46
|
#32
|
Erfahrenes Mitglied
Registriert seit: 22.02.2012
Ort: DK
Fahrzeug: Mercedes W203, 1,8 Kompressor Coupe +Honda Magna 750V4
|
Doch Dexron 3 ist Vollsynthetisch. Besonders gut für die 4HP22/24, da diese eigentlich eine sehr geringe Ölmenge Beinhalten und deshalb das Öl sehr warm werden kann. Dexron 3 hat einen Flammpunkt von 240 Grad, wogegen Dexron 2 nur einen Flammpunkt bis 120 Grad hat.
__________________
Es ist schon erstaunlich, wie der Mensch an seinem Leben hängt, obwohl er es so hasst.
|
|
|
05.07.2020, 02:51
|
#33
|
Shogun
Registriert seit: 19.07.2002
Ort: Joso
Fahrzeug: E32 750iL 11/88
|
Zitat:
Zitat von Andrew1Q
What will happen if kick down switch not grounded of rust floor ? Will car go to limp mode ?
|
no, it will not go into limpmode, I explained that already on Bimmerforums to you, your car has no EML, see here https://www.7-forum.com/forum/showth...light=kickdown
you can test it: Schau dir den Kickdown-Schalter an, der sitzt als Gummiblock hinterm Gaspedal, dort sollen 5 Volt sein, und wird beim drücken auf Masse geschaltet. Das kannst am Getriebe-Steuergerät Pin 2 Kabel grün/gelb Messen.
----
So measure on the transmission control unit pin 2 cable green/yellow
|
|
|
05.07.2020, 09:41
|
#34
|
Neues Mitglied
Registriert seit: 25.06.2020
Ort: Ukraine
Fahrzeug: BMW E32-735i (02/1990)
|
Do you know what engine oil pressure should be at PSI gauge if installed to somewhere at cylinder head ?
|
|
|
05.07.2020, 13:15
|
#35
|
Shogun
Registriert seit: 19.07.2002
Ort: Joso
Fahrzeug: E32 750iL 11/88
|
The German repair manual from Bucheli for the E32 series has following info for the oil pressure
for the M30B30 and M30B35
oil pressure in idle 0.5-2.0 bar
oil pressure at max RPM 4.0-6.0 bar.
radial tolerance outer rotor/pump housing 0.1-0.15mm
axial play
rotor/pump housing 0.04-0.1mm
space inner/outer rotor 0.12-0.20mm
length of the over pressure spring without tension 68mm
|
|
|
Aktive Benutzer in diesem Thema: 1 (Registrierte Benutzer: 0, Gäste: 1)
|
|
Forumregeln
|
Es ist Ihnen nicht erlaubt, neue Themen zu verfassen.
Es ist Ihnen nicht erlaubt, auf Beiträge zu antworten.
Es ist Ihnen nicht erlaubt, Anhänge hochzuladen.
Es ist Ihnen nicht erlaubt, Ihre Beiträge zu bearbeiten.
HTML-Code ist aus.
|
|
|
|